C-130 Technical
1,312 topics in this forum
-
- 10 replies
- 1.2k views
Is it possible stowage rod upper bracket quick release pin came off from it's hole during flying/takeoff/landing
Last reply by munirabbasi, -
-
- 4 replies
- 899 views
Hi folks. Looking to verify something I was told recently about SEA vintage C-130s. Was it possible to lower the ramp/open the cargo doors in flight from the flight deck? If so, would that have been done by one of the pilots or the FE? Thanks
Last reply by jconner2, -
- 3 replies
- 1.1k views
Curious if any of you remember the ASC engineering team (me and a young captain) who went around the world giving a briefing on this ditching? We also did a video of the briefing some of you might have seen. I was told the briefing was still being shown well into the late 90s.
Last reply by Duke, -
- 4 replies
- 1.1k views
I am currently facing a challenge where my APU generator OUT light comes ON, but the frequency and voltage is with allowable limit, also, there is load indication. We have changed the contactor, Voltage regulator and the even the APU regulator but the discrepancy persist. Pls I will appreciate any quick response . Thanks
Last reply by Kaydee, -
- 0 replies
- 485 views
i am finding nutplates spec(part no’ and nsn) for 2 lug floating replaceable nut nutplate location is in engine heat shield both lug hole distance is about 1” nutplate for L3 screw nutplate image likes follows please let you guys know nutplate spec thanks for your response
Last reply by KHJ, -
- 0 replies
- 412 views
am looking for the GTCP85-8498 (I know it was a modification used by the British company AVIATION TURBINE SERVICES, Ltd, which no longer exists). Does anyone know how I can get said model or how to transform a standard GTCP85 to said series? Thanks
Last reply by Jorge Lluch, -
- 0 replies
- 861 views
I need soft copy of TO 11A18-14 Best regards Munir abbasi
Last reply by munirabbasi, -
- 1 follower
- 4 replies
- 1.6k views
At the end of the flight, when the aircraft is reconditioned: When I set the Air conditioning Master Switch to OFF or AUX VENT, the breaker cabin press and AUX Vent triggers after 2 seconds. On positions NO PRESS, PRESS MAN or AUTO PRESS, the breaker does not trip ... I have a doubt about a piece of equipment but I would like to have your avionics opinion. Thank you
Last reply by Check Team FR, -
- 2 replies
- 695 views
Reasons of burning out of Heading Coupler #1. Two Heading Couplers got burned in #1 position, one after another, while voltage and wiring found okay.
Last reply by tinyclark, -
- 2 replies
- 971 views
Hello everyone, For the past month or two we've been having an ongoing issue with pressurization on our J model. The problem typically gets recognized when flying at higher altitudes, 19-20k ft, thought recently they've stated they had erratic pressurization at all altitudes. Initially the problem was erratic pressurization throughout flight, resulting in ears popping and discomfort, when at higher altitudes they received a CAB Alt high advisory because cab alt was indicating above 10k ft. We change a part, it flys 1-2 times and the problem comes back. We've changed the outflow vlv, cabin pressure controller, vacuum reg, and servo valve, some things have been cha…
Last reply by munirabbasi, -
- 9 replies
- 1.1k views
Hye guys. I really need help. I had an experienced on this issue. Mine generator disc indicator on the overhead panel not illuminate during test. Before test, my aircraft do experience generator out light and failed bearing light illuminate in flight. Pilot tried to disconnect the generator with the gearbox using generator disconnect system, however the indivator didnt illuminate and it forced pilot to shutdown #3 engine to avoid catastrophic mechanical failure. On the rectification after the flight, it found that the generator had broken with shaft do also broken. From my understanding, failed bearing light is due to mechanicle failure or maybe due to the broken of the g…
Last reply by munirabbasi, -
Hi i wanna ask you about the elevator and its relation with the elevator trim tab, when the nose is Down what's the position of elevator and the trim tab?
Last reply by munirabbasi, -
- 1 reply
- 578 views
Hi Folks, I'm currently planning a new module, the fuel-management. Can anybody help me with the question why the fuel management panel of a J-model (the one with the rotary switches and digital readouts) has only one tank selector? What is that rotary switch controlling? I dont find anything about a fuel selector in the public available schemata. Regards Thomas If anybody ist interested in the current status of my sim: https://c130-sim.weebly.com/
Last reply by munirabbasi, -
- 4 replies
- 882 views
Hello Herc masters!I"ll be thankfull if you could provide me Drawing no. 3305083 Rev. A, necessary for applying SB 82-790 CW Widepread Fatigue Damage Inspections and TCTO 1C-130-1908.Thank you very much!
Last reply by munirabbasi, -
GTC problems 1 2
by mike in ca- 25 replies
- 12.8k views
I am having problems with a GTC not running without a boot pump. After the boost pump is turned off, about the time the manifold pressure gauge hits 5lbs the GTC dies. With a boost pump on the GTC will handle the load of the ATM and both AC packs on, the GTC will die with no load also as soon as the boost pump is turned off. I have checked the cracking pressure and it is at 61lbs, the armpit valve is working as it should. The gtc fuel filter was replaced and still no difference. Anyone ever had this problem?
Last reply by Jbas130, -
- 0 replies
- 576 views
If any AE 2100D3 engine prop balance sometimes detected and didn’t do any rectification jobs. What are the problems will be happened? Please give me Any practical or theoretical idea. Thanks
Last reply by sharif101, -
- 1 reply
- 568 views
Hello Herky people, I want to know how to use exterior lightning on the ground (day/night),in flight(day/night) depending on weather condition. thanks
Last reply by NATOPS1, -
- 8 replies
- 3.6k views
HI GUYS. VERY GOOD EVENING. IM FACING A DEFECT NO 1 ENGINE RPM INDICATOR NIL INDICATION DURING START UP ( FROM 0% DIRECTLY JUMP TO 22% RPM) WITH OTHERS ENGINE INSTRUMENTATION NORMAL. WE ALREADY DID THE RECTIFICATION BY SWAP AND REPLACE INDICATOR, REPLACE ECTM CONVERTER REPLACE 3 X TACHOGNY REPLACE VALVE HOUSING WIRING CX ON THE SYSTEM DO YOU GUYS HAVE ANY IDEAS ON THIS DEFECT??
Last reply by M Ahsanul Haque Mukul, -
- 1 reply
- 683 views
KC-130T buno 313 and up, Having an issue where the CARA will lose altitude intermittently while in flight. Sometimes it will happen on takeoff or descent other times it will happen while cruising. (Aircrew will sometimes associate it with nav select switching but cannot be duplicated) CARA will fluctuate under 50 feet while airborne causing GPWS to go off for low altitude sometimes resetting the breaker will return it to normal other times if terrain changes it will return to normal on its own. Have replaced pilots indicator, CARA R/T and antennas but gripe still remains. Also I have shot the cables with a TDR and they seem normal. Any insight would be greatly apprec…
Last reply by tinyclark, -
- 3 replies
- 935 views
Hello all, Working on a KC-130T-30 and having an issue with the #2 and #4 generators holding a load. Replaced multiple components: #4 gen contactor, one of the bus tie contactors, #2/4 GCP, #4 voltage regulator. Generators will power on and give good freqs and voltages but when switched to on will not carry essential bus or a heavy load. Occasionally we can get either to pick up a bus or remove applied loads and slowly turn items on till the gen out light illuminates and freq and volts are zero. Have verified wire continuity and voltages while gen is operating normally everything checks good. When gen is in a failed state the normal voltage at the voltage regulator …
Last reply by Fargusmcg, -
- 8 replies
- 1.8k views
Hello T56A -15 power plant Pneumatic Expertise T56A-15 (C-130 E model) engine can provide approximately 155 pounds of air flow per minute at 635F and 125 pounds per square inch of gauge pressure. Bleed manifold pressure gauge is mounted in F/deck (direct gauge) display approximately 70 PSIG .where remaining pressure of the engine flow? Best Regards Munir Abbasi Home of Hercules Pakistan
Last reply by munirabbasi, -
- 4 replies
- 1.6k views
Hello Herks Hydra Expertise! 1. It has mentioned Intermediate level maintenance T.O of EDP NYAB at 3000 RPM , flow rate of pump is 6 GPM min, where pump is designed 10 GPM at 3650 RPM . when both the pumps (NYAB) In Aircraft utility system working parallel max flow ie 16.93 pressure drop to 1800 psi. how we can calculate flow rate (GPM) of both NYAB pumps when they are working parallel at 3000 RPM? 2 Just assume that aircraft hydraulic utility system ,when No 1 EDP pressure is 3000 psi and No.2 EDP pump pressure 3100 psi how the pressure act passes thru passage of single pipe after isolation check valves ? Best Regrads Munir Abbasi Ho…
Last reply by munirabbasi, -
- 4 replies
- 1.1k views
Hello Pneumatic expertise Identify and purpose of mark image Munir Abbasi Home of hercules Pakistan
Last reply by NATOPS1, -
- 6 replies
- 3.3k views
Hi guys, just curious for knowledge sake, for 3505786-1 air turbine starter, when inflight suddenly start valve light illuminate and start valve open, will the air turbine starter crank and get damaged? Thanks.
Last reply by NATOPS1, -
- 0 replies
- 489 views
good evening to everybody im experiencing a "RADAR DEGRADED" CAUTION ACAWS on a C130J with a generic diagnostic message LPCR BIT FAIL FC3442010. The radar seems to work fine but after the power up bit completes the CAUTION pops up, troubleshooting the fault isolation for this fault codes nothing looks bad. I replaced all the LRUs and the ECBUs which apply power to the system. Any hint?
Last reply by sasa71,
