Ahmer
Members-
Posts
88 -
Joined
-
Last visited
-
Days Won
3
Content Type
Profiles
Forums
Store
Gallery
Downloads
Calendar
C-130 Hercules News
Everything posted by Ahmer
-
Dear Tiny, I have all these information, but I want to know when this is inoperative on B & E aircrafts. Intialy which TCTO, Service nees, service later or SB issued for these system to inoperative .tnx Regards
-
Hello Experty , Nacelle preheat system inoperative in c130 B & E aircraft, plz any body knows about why this system inoperative,any TCTO or SB referance for deactivates this system, plz share Regards
-
If fluctuation is in all modes,Most probably cause of valve housing.
-
Hello, at that time ur prop is in normal governing mode or in mechanical mode? If fluctuation is in both modes then change v/Housing filter and then valve housing. Most probably cause of valve governor. Regards
-
C130 E model no regulator bleed valve used in horse collar, these are motor operated bleed valve . When we used no3 psn bleed for anti icing the torque also rise instead of TIT.
-
When disconnected the hose from FCU & anti icing on how to increase the fuel flow in fcu bleed no added or entering in CIP bellows?
-
Its increase when we on wing and ampen anti icing on & duct anti icing switch Off psn ay that time.
-
Not with all four engines only with no 3 psn engine.
-
Hello expertise T56-a-15 engine at abt 900 TIT when we open wing & empen anti icing TIT remains same but torque of respective engine increase, when close the torque decreases. if any body having good information plz share with us. Regards
-
Hi dear paulo, LSGI RPM is 75% & NGI RPM is 95% , what will be ur decision in this situation. How we increase NGI RPM ? Regards
-
Hello expertise, Any body knows about replenishing cycle of Hydraulic MIL-H-83282 on c130 aircraft hydraulic systems. Please informs with Technical order Reference. Tnx
-
Plz installed TD tester, it will identify the component which having problem, if u haven't TD tester and u replaced all components of TD system u also replace LT harness assy, it might be resolve ur problem.
-
Pj, if u change FSR ,AC cont panel and Generator. U should go to Replace FCU because there is no adjustment of GI & FI rpm if prop angle is with in limit. Regard
-
Hello pj , when u put the engine to normal ground idle, Gen frequency on frequency meter available at GEN switch on OFF position.?
-
If u replaced all thing plz check or replaced auxiliary start relay.
-
Hello, replace APU fuel atomaizer most probably cause of this component.
-
In Null u must very careful while moving throttle because u havn't overtemprature protection.
-
Bleed valves sticks ,s.s valve malfunction.
-
This is correction of TIT 15 to 60 °c not a cut back its miss consecpt.as per 1c-130B-2-4CL-1. But new JG 1c-130H-2-71JG-00-1 having no 15 to 60°c limit its only 800 to 840 limit of cross over TIT no correction mentioned here.
-
The dual brake control valve have a metering valve piston is hollow with series of radial at return port end.An over pressure condition in the brake assembly ,caused by thermal expansion ,is automatically relieved by metering valve piston. Regard
-
Yes if NTS system fail prop RPM will be more then power section at that time propeller RPM cross the limit 103.5 . it should be pitch locked and aircraft will yaw opposite direction. If Negative torque increases limit -6000 torque RGB Decoupled from power section. Definitely if outer engine is pitch lock and pilot not confirmed the torque should be more when throttle retarted & aircraft will be yawning opposite direction.we experienced of Pitch lock during NTS system failure during decsanding,Fault is with NTS bracket which not properly actuate NTS system.
-
NTS system works above flight idle, NTS system work when prop try to rotate engine (during descending,gust load,interruption in TD system,and improper governing) when propeller try to rotate engine (negative torque ) produce this system increase the blade angle when blade angle increase prop RPM decease become in governing range RPM. If ur NTS system fail during descending & NTS system not increasing blade angle through feathering valve and propeller RPM increases obve the pich lock RPM limit ( above 103.5) then propeller should be pitch lock. U can observed pich lock propeller by moving the throttle forward engine RPM follow the throttle movement & torque will be same its indication of pitch lock. REGARDS
-
Rudder Boost Diverter Valve Manual Override Button
Ahmer replied to dagebow's topic in C-130 Technical
It is installed on deverter panel at devert valve on both side utility & booster .regards -
INOPERATIVE WINDSHIELD ANTI−ICING Operation with inoperative windshield anti−icing is permissible provided. 1. The airplane is not flown in known icing. 2. The maximum speed limit below 10,000 feet is 185 KIAS due to possible bird strikes. Descent from high altitude into warm moist air with an inoperative nesa windshield anti−icing system will cause fogging and possible icing of the windshield. To minimize this, increase cabin air temperature and open the pilot’s and copilot’s windshield defogging valves. It is recommended that a gradual descent be made to allow the windshield, which has been cold−soaked at altitude, to warm with ambient cabin air.