C-130 Technical
1,312 topics in this forum
-
Struts
by Leakybirds- 5 replies
- 1.4k views
How often do you completely drain and fill struts? And do you use hydro mite?
Last reply by hehe, -
-
Does anyone know what would be Suggested Tolerance Values while Engine is not running? See below. Engine Oil Pressure 0-2 psi Gearbox Oil Pressure 0-3 psi Oil Cooler Flap Pos. 0-5 per cent Fuel Flow 0-50 pph
Last reply by Antonio, -
- 2 replies
- 920 views
What could be causing a slow moving utility gauge. Pressure reads fine on aux pump, normal and emergency gauge. Just utility gauge shows hesitation. Transmitter and gauge have been replaced. Could it be the util accumulator? Thanks for the help.
Last reply by munirabbasi, -
- 0 replies
- 390 views
Hi everybody, Can anyone guide how to interpret Remote Electronic Unit (REU6100) fault codes made by Becker-Avionics? Thank you
Last reply by Danoo, -
- 4 replies
- 1.1k views
Difference between rosemount and nonrosemount pitot static system.
Last reply by NATOPS1, -
- 5 replies
- 830 views
Greetings, We’ve been having an ongoing RTRU issue that only occurs in flight, usually a couple of times during touch and gos/takeoff. TR3 load will drop below 5, kick out a fail for 2-3 seconds then recover and go back to functioning properly. A few things we’ve changed include the TR unit, BIU, as well as the associated diode. Was curious if anyone has seen a similar issue or has any input on potential culprits. All meter readings weve checked have been good, as it does not fail on ground.
Last reply by tinyclark, -
- 0 replies
- 440 views
Hi C-130 Forum, Could some one advise if Technical Order 6-1-111 "General Cleaning and Testing 1" is available, or has been replaced? This document is referenced in the Maintenance Data we hold. I am hoping that this document has been replaced by a Robins AFB TO for Public Access. Any help would be greatly appreciated. Many thanks.
Last reply by Deputy Dog, -
- 0 replies
- 481 views
Anyone can give suggestions about AE2100D3 engine propeller gearbox vibration, within two years four engines vibration and one engine PGB gear damaged,it’s too much trouble.
Last reply by sharif101, -
- 1 reply
- 619 views
Hello brother In C-130B model, if VHF 1 or 2 is selected from either pilot or copilot side ,, the RT reception is also found from opposite position, that is if VHF 1 is selected from captain side, Copilot can here that call at the same time in a large volume. Where could be the problem?? Nav side and Flt engr position is ok.. only problem with pilot and copilot side. Thank you in Advance
Last reply by NATOPS1, -
- 2 replies
- 668 views
Is there any body that can give me the T.O. for the P/N 23086057 Prop Flange Shaft Adaptor of the AE 2100 D3 engine. We need to get this manual but the Government entity only replies to TO numbers AE2100D3.pdf
Last reply by Bogi252, -
- 1 reply
- 484 views
Hi!! Hope you are fine and well. Need to ask few information regarding the SATCOM used in C130. The Euronav RN7 working is not getting clear. Can you guide about the working of RN7? What medium it uses and the complete mechanism of its working? Facing few issues of its call, network and signals. I will be highly obliged if you can share all the information regarding RN7.
Last reply by Danoo, -
- 1 reply
- 732 views
Hello! We’ve recently ran into an issue on our C130J with a get home control panel lighting. The panel lights up and is fully operation with external power, however on just battery power the lighting is inop. It will still transmit, but the lighting is completely inop. We’ve ohms checked most associated wiring good, swapped get home control panels, BAU, as well as the emer lighting module to no avail. anyone have any experience with something similar or have any input? thanks!
Last reply by hehe, -
- 3 replies
- 936 views
can anyone explain me how to work SPR pressure tester ? . please I need more information about this apparatus
Last reply by mecano flyer, -
- 10 replies
- 1.2k views
Is it possible stowage rod upper bracket quick release pin came off from it's hole during flying/takeoff/landing
Last reply by munirabbasi, -
- 3 replies
- 1.1k views
Curious if any of you remember the ASC engineering team (me and a young captain) who went around the world giving a briefing on this ditching? We also did a video of the briefing some of you might have seen. I was told the briefing was still being shown well into the late 90s.
Last reply by Duke, -
- 4 replies
- 922 views
Hi folks. Looking to verify something I was told recently about SEA vintage C-130s. Was it possible to lower the ramp/open the cargo doors in flight from the flight deck? If so, would that have been done by one of the pilots or the FE? Thanks
Last reply by jconner2, -
- 0 replies
- 495 views
i am finding nutplates spec(part no’ and nsn) for 2 lug floating replaceable nut nutplate location is in engine heat shield both lug hole distance is about 1” nutplate for L3 screw nutplate image likes follows please let you guys know nutplate spec thanks for your response
Last reply by KHJ, -
- 0 replies
- 425 views
am looking for the GTCP85-8498 (I know it was a modification used by the British company AVIATION TURBINE SERVICES, Ltd, which no longer exists). Does anyone know how I can get said model or how to transform a standard GTCP85 to said series? Thanks
Last reply by Jorge Lluch, -
- 0 replies
- 883 views
I need soft copy of TO 11A18-14 Best regards Munir abbasi
Last reply by munirabbasi, -
- 15 replies
- 1.5k views
This particular sbag has been disturbing the team for the oast few weeks. What could be the cause, we have replaced the control unit, antenna and also TR unit. Checked every component in the system for serviceability but it still persists.
Last reply by tinyclark, -
- 2 replies
- 1k views
Hello everyone, For the past month or two we've been having an ongoing issue with pressurization on our J model. The problem typically gets recognized when flying at higher altitudes, 19-20k ft, thought recently they've stated they had erratic pressurization at all altitudes. Initially the problem was erratic pressurization throughout flight, resulting in ears popping and discomfort, when at higher altitudes they received a CAB Alt high advisory because cab alt was indicating above 10k ft. We change a part, it flys 1-2 times and the problem comes back. We've changed the outflow vlv, cabin pressure controller, vacuum reg, and servo valve, some things have been cha…
Last reply by munirabbasi, -
Hi i wanna ask you about the elevator and its relation with the elevator trim tab, when the nose is Down what's the position of elevator and the trim tab?
Last reply by munirabbasi, -
- 1 reply
- 600 views
Hi Folks, I'm currently planning a new module, the fuel-management. Can anybody help me with the question why the fuel management panel of a J-model (the one with the rotary switches and digital readouts) has only one tank selector? What is that rotary switch controlling? I dont find anything about a fuel selector in the public available schemata. Regards Thomas If anybody ist interested in the current status of my sim: https://c130-sim.weebly.com/
Last reply by munirabbasi, -
- 9 replies
- 1.2k views
Hye guys. I really need help. I had an experienced on this issue. Mine generator disc indicator on the overhead panel not illuminate during test. Before test, my aircraft do experience generator out light and failed bearing light illuminate in flight. Pilot tried to disconnect the generator with the gearbox using generator disconnect system, however the indivator didnt illuminate and it forced pilot to shutdown #3 engine to avoid catastrophic mechanical failure. On the rectification after the flight, it found that the generator had broken with shaft do also broken. From my understanding, failed bearing light is due to mechanicle failure or maybe due to the broken of the g…
Last reply by munirabbasi, -
- 2 replies
- 731 views
Reasons of burning out of Heading Coupler #1. Two Heading Couplers got burned in #1 position, one after another, while voltage and wiring found okay.
Last reply by tinyclark,